Skip to main content

Al Siraj Electronics Repairing

24/7 Help Line - 054 309 2041

Book AL SIRAJ ELECTRONICS REPAIRING Service on just one call

Chat on WhatsApp

Get Rapid Response Service on WhatsApp

AC Repair

AC Error Codes Explained: Daikin, Midea, Samsung and LG in Dubai

By Al Siraj Electronics RepairingUpdated 10 min read

AC Error Codes Explained: Daikin, Midea, Samsung and LG in Dubai - Al Siraj Electronics Repairing Dubai

AC error codes are short letter-and-number messages your air conditioner (AC) shows when its control board spots a fault in a sensor, motor, power supply or the link between the indoor and outdoor units. A blinking light or a code like U4, E1 or CH05 does not always mean a big repair, but you should not ignore it.

This guide explains the common codes for Daikin, Midea, Samsung and LG in plain words, tells you what you can safely try, and shows when to WhatsApp Al Siraj Electronics Repairing for AC repair service in Dubai. Codes vary by model, so your label and manual always come first.

Key point: A code tells you where the board found a problem. It does not tell you which part has failed. A technician still has to test the part before anything is replaced.

What Do AC Error Codes Mean?

An AC error code is a fault message from the unit’s control board. The board checks sensors, fan motors, the compressor drive and the signal between indoor and outdoor units. When a reading is wrong, it stops the unit to protect it and shows a code or blinks a light.

The same letters can mean different things on different brands, and even on different models of one brand. That is why a code from a web list is a clue, not a diagnosis. Manufacturer support pages say the same: Samsung’s own page notes that code meanings can vary by model and tells owners to check the user manual.

What Should You Do First When Your AC Shows a Code?

Write down the code, then switch the AC off at the remote and at the breaker. Wait about five minutes, switch the breaker back on and restart. Clean the indoor filter first if it is dusty. If the code returns, stop using the unit and call a technician.

Four wall-mounted air conditioning units on a grey panelled wall
Photo by Kien Nguyen on Unsplash

The five-minute wait is the reset method LG gives on its support page, and Daikin’s manual also says to turn the breaker off and on after cleaning the filters. A one-off power glitch can set a code that clears on restart.

  1. Note the code, the brand and the model. Take a photo of the display or blinking lights.
  2. Turn the AC off at the remote, then at the breaker.
  3. Slide out the indoor filter, rinse it, dry it and refit it. Make sure nothing blocks the air inlet or outlet.
  4. Wait about five minutes, then restore power and start the AC.
  5. If the same code appears again, leave the AC off and arrange an on-site inspection.

Safety note: Do not open the casing, touch wiring or handle refrigerant. Control boards, compressors, refrigerant and electrical work are for technicians only.

Need a quick opinion? WhatsApp a photo of the code and your model label to +971 54 309 2041 and we will give you a quick estimate.

What to do when an AC shows an error code: note the code, power off, clean the filter, wait 5 minutes, then arrange an inspection if the code returns
Infographic: what to do first when your AC shows an error code

What Do Daikin AC Error Codes Mean?

Daikin codes usually start with a letter such as A, C, E, F, H, J, L or U. Daikin’s own operation manual for one split range lists U4 as a transmission failure between indoor and outdoor units, A5 as freeze-up protection and E1 as a circuit board fault. Check your model’s manual.

The table below uses the fault diagnosis list in a Daikin split-system operation manual. Your model may differ.

CodeMeaning in plain wordsOwner check or technician job
U4The indoor and outdoor units are not talking to each otherReset once. If it stays, technician: wiring, connectors or board
U2Supply voltage dropped or the main circuit saw too high a voltageReset once. If it repeats, technician should test the supply and the board
U0Refrigerant shortageTechnician only: leak check and refrigerant work
A5High pressure control or freeze-up protectionClean filter, clear airflow, reset. If it repeats, technician
A6Indoor fan motor faultTechnician only
E1Outdoor circuit board faultTechnician only
E6Compressor start-up faultTechnician only

For a blinking lamp with no code, Daikin’s manual says to clean the filters, clear any blocked inlets and outlets, switch the breaker off and on, and call the service shop if the lamp still flashes.

What Do Midea AC Error Codes Mean?

Midea indoor units show codes such as E1, E2, E3, P1 or P4 on the display. In one Midea split-system service manual, E1 is an indoor and outdoor communication protection, and P1 is an over-voltage or low-voltage protection. Your model’s list may differ, so check its manual.

CodeMeaning in plain wordsOwner check or technician job
E1Communication problem between indoor and outdoor unitsReset once. If it stays, technician
E3Indoor fan speed out of controlCheck the filter and airflow. If it stays, technician
E6Room or evaporator temperature sensor open or short circuitTechnician only
P1Over-voltage or too-low voltage protectionReset once. If it repeats, technician should test supply and board
P4Inverter compressor drive errorTechnician only

What Do Samsung AC Error Codes Mean?

Samsung splits its display messages into information codes and error codes. CF is a filter cleaning reminder, DF means the unit is defrosting, and E-codes such as E101 or E121 are faults. CF means clean the filter and DF means wait for the defrost to finish. Do not treat either as a fault.

CodeMeaning in plain wordsOwner check or technician job
E101, E102, E202No communication between indoor and outdoor unitsReset once. If it stays, technician
E121, E122Indoor room or pipe sensor faultTechnician only
E461Compressor start faultTechnician only
E472AC voltage signal faultReset once. If it repeats, technician
E554Gas leak faultTechnician only

What Do LG AC Error Codes Mean?

LG’s support pages group its CH codes by problem type. CH05, CH53 and E0 point to a communication problem between the indoor and outdoor units. CH32, CH33, CH36, CH38 and F4 point to a refrigerant or compressor-related problem. CH66 and CH90 to CH93 point to installation or test-run problems.

Code groupMeaning in plain wordsWhat LG advises
CH05, CH53, E0Indoor and outdoor units not communicating. Causes include a power glitch, wiring, a loose connector or the main boardReset. If it stays, stop using the unit and get it inspected
CH32, CH33, CH36, CH38, F4Refrigerant or compressor-related problemReset. If it stays, stop using the unit
CH66, CH90 to CH93Wiring, incomplete test run or restricted refrigerant flow after installationRight after installation, contact the installer

LG warns owners not to take the AC apart. We agree.

What About Gree AC Error Codes?

Gree units also use letter-and-number codes or blinking light patterns. We have not listed Gree codes because we could not verify them against a manufacturer source. Check your manual or send Al Siraj a photo. We repair Gree, Daikin, Midea, Carrier, Trane and York units, plus Samsung and LG. See brands we repair.

Can You Reset the Code or Should You Call a Technician?

You can try one reset and a filter clean. If the code is gone and the AC cools normally, keep an eye on it. If the code returns, or the code points to a board, compressor, sensor, fan motor or refrigerant, call a technician.

White air-conditioning condenser unit fixed to an outside wall
Photo by Annie Spratt on Unsplash
SituationWhat to do
Code cleared after one reset and the AC coolsKeep using it. Clean the filter. Book an inspection if it returns
Same code returns within daysStop using the AC and book an on-site inspection
Code points to the board, compressor or refrigerantTechnician only
Breaker keeps tripping with the codeLeave the AC off and call

Money-saving tip: One reset is a sensible test. Five resets will not fix a failed part, and waiting can let a small fault grow.

If the code points to a compressor problem, our guide on AC compressor repair or replace explains the decision. If it points to a refrigerant fault, read AC gas refill or leak repair.

Why Does Dubai Make AC Error Codes More Common?

Dubai conditions push AC control boards harder. Voltage swings at peak summer demand can trigger supply and inverter protection codes. Dust and sand clog filters, coils and outdoor fans, so units overheat and trip protection. Summer heat over 45°C adds load on every part.

  • Voltage swings at peak demand can set supply codes like U2 or P1 and stress the inverter board.
  • Dust on filters and coils makes the unit run hot, which can set temperature or fan codes.

Servicing the filters and coils before summer lowers the chance of these codes. Our AC repair guide for Dubai covers the full picture, and AC stopped at night explains the common overnight shutdown.

How Does Al Siraj Fix an AC Error Code Fault?

Al Siraj is an independent repair company. We do not claim any brand authorisation. We read your code, test the part behind it, quote a fixed price before work starts and repair at your door. Most repairs take 30 to 60 minutes after diagnosis.

  1. Book and get a quote. Call or WhatsApp us with the code and a photo of your model label. A technician reaches your door in under 60 minutes on average, 24 hours a day, 7 days a week.
  2. On-site inspection. We read the code and test the sensors, fan motors, wiring and board. A diagnostic fee may apply and is usually included in the total if you go ahead.
  3. Immediate repair. You get a fixed quote before we touch it, with no hidden fees. We use genuine parts and repair the same day.
  4. Warranty and aftercare. The repair is tested in front of you. You get a 12-month written warranty on the invoice for the fault repaired and the parts we supply and fit.

Al Siraj has served 3,000+ clients over 7+ years in Dubai, with a 95% first-visit fix rate. Read about our AC repair service or visit about us.

Frequently Asked Questions About AC Error Codes

Why is my AC blinking a light and not cooling?

A blinking light usually means the control board has stopped the AC after finding a fault. Clean the filter, switch off at the breaker for five minutes and restart. If it still blinks, the fault is real and a technician should inspect it.

Can I reset my AC error code myself?

Yes, once. Switch the AC off at the breaker, wait about five minutes, then restore power. If the code comes back, stop resetting. Repeated restarts do not fix a failed part, and the fault may get worse.

Do AC error codes mean the same thing on every brand?

No. The same code can mean different faults on different brands and even different models. E1 is an outdoor board fault on one Daikin manual and a communication protection on one Midea manual. Always check your own model’s manual or label.

Can voltage swings in Dubai cause AC error codes?

Yes. Supply voltage that drops or spikes can set protection codes and stress the inverter board. Codes like Daikin U2 or Midea P1 relate to voltage. If one repeats, a technician should test the supply and the board, not just reset it.

How much does it cost to fix an AC error code?

The cost depends on which part is behind the code, such as a sensor, fan motor or board, and on your model. We quote a fixed price before work starts. WhatsApp a photo of your model label for a quick estimate.

Will the repair come with a warranty?

Yes. Al Siraj gives a 12-month written warranty on the invoice. It covers the fault repaired and the parts we supply and fit. It does not cover new unrelated faults, misuse, power-surge damage, wear on consumables or later third-party work.

Last updated: 9 November 2026

Got a blinking light or a code you cannot read? Call +971 54 309 2041 or WhatsApp us a photo of the code and your model label. You can also use online booking.

Contact Al Siraj Electronics Repairing

Arab Bank Bldg – Office No SM1-02-710 – Port Saeed – Riggat Al Buteen – Dubai – United Arab Emirates
Phone and WhatsApp: +971 54 309 2041
Open 24 hours, 7 days a week