Skip to main content

Al Siraj Electronics Repairing

24/7 Help Line - 054 309 2041

Book AL SIRAJ ELECTRONICS REPAIRING Service on just one call

Chat on WhatsApp

Get Rapid Response Service on WhatsApp

Dishwashers

Dishwasher Error Codes: Bosch, Siemens, Samsung and LG in Plain Words

By Al Siraj Electronics RepairingUpdated 10 min read

Dishwasher Error Codes: Bosch, Siemens, Samsung and LG in Plain Words - Al Siraj Electronics Repairing Dubai

Dishwasher error codes tell you which system has faulted, such as drainage, water inlet, heating or a leak. Some clear with a clean filter or an open tap. Others, such as a water-protection code, mean stop and call. Codes vary by model, so check your label and manual before you act.

Al Siraj Electronics Repairing offers dishwasher repair service in Dubai for Bosch, Siemens, Samsung, LG and other brands, with a fixed quote before work starts. Call +971 54 309 2041 or send the code and a model label photo on WhatsApp.

Below are tables for each brand and a clear line between reset and call. We list only codes we could check against the makers’ own support pages.

What Should I Do When My Dishwasher Shows an Error Code and Stops?

Note the code, switch the dishwasher off at the breaker, close the water tap and mop up any water. Take a photo of the display and the model label. Then check the cause in the brand table below. If the code mentions a leak, heater or board, call a technician.

Safety note: Isolate the water and the power before you touch the filter, hoses or seal. Do not open panels or test wiring.

  1. Photograph the display before you switch off.
  2. Close the isolation tap and switch off at the breaker.
  3. Find your code in the table for your brand.
  4. If the cause is a filter, tap or hose, fix it, then run one short cycle.

Can I Reset a Dishwasher Error Code, or Should I Call?

You can try one reset. Bosch’s US instructions are to turn the dishwasher off or switch off the breaker for about a minute, turn it back on and run a short empty test cycle. If the code returns, stop and call. Repeated resets do not repair a failed part.

Mug loaded in a dishwasher rack
Photo by Mohammad Esmaili on Unsplash
SituationSafe actionCall a technician if
Code appears once after a power cut or a dipOne reset, then a short empty cycleThe code comes back
Drain or filter codeClean the filter, check the hose for kinksWater still stands in the tub
Water supply or inlet codeOpen the tap fully, check the hose for kinksThe tub still does not fill
Leak or water-protection codeClose the tap, switch off, mop up. Do not reset to test itAlways. A technician finds the source
Heater, sensor or board codeOne reset onlyThe code returns, or the machine will not run

Key point: The code names a circuit, not always a part. A code for a heater can come from the sensor, the wiring or the board. A technician tests before replacing anything.

Bosch Dishwasher Error Codes: What Do E15, E24 and E25 Mean?

On Bosch dishwashers, E15 means the leak safety switch has detected water in the base, E24 means the drain is blocked and E25 means the drain pump is blocked. E22 is a blocked filter. Many other codes need a technician.

CodeWhat Bosch saysReset or call
E15Safety switch detected water in the base, so leak protection has activatedClose the tap, switch off, call
E22Filter blockedClean the filter, then retest
E24Drain blocked. Check the hose for kinks and that the pump cover is secureCheck, then call if it persists
E25Drain pump blocked, or pump cover loose or missingCall if the pump needs clearing
E16 or E17Water may not be entering. Check the inlet hose is not kinkedCheck hose, then call
E12Limescale in the heat pumpCall. Descaling is a technician job
E09Listed on Bosch’s US page as a heat pump internal heater fault. Other regional pages say not to self-repairOne reset, then call
E27House power supply too lowReset once, then check the incoming power

The Bosch pump cover sits under the filter, behind water and wiring. Bosch’s own page notes that debris there may be sharp. We treat pump clearing as technician work. See our Bosch dishwasher repair in Dubai page.

Siemens Dishwasher Error Codes: What Do They Mean?

Siemens dishwashers show codes such as E15 for water protection and E24 for a blocked drain. Siemens tells you to close the tap, switch off and call for water-protection codes.

CodeWhat Siemens saysReset or call
E15 or F15The water protection system has been activated. Do not self-repairClose the tap, switch off, call
E24 or F24A blocked pump is a likely cause. Check it, and if the problem persists, close the tap and switch offCall if it persists

Siemens publishes more codes than we list here, and they vary by model, so confirm against your manual. See Siemens dishwasher repair in Dubai.

Samsung Dishwasher Error Codes: What Does the LC Code Mean?

On a Samsung dishwasher, LC or LE means a leak issue, 5C or 5E means a drainage issue, and 4C or 4E means a water supply issue. For the LC code, tighten loose hose connections, check the machine is level and clean the filter. If it continues, call for service.

CodeWhat Samsung saysSafe checkCall if
LC or LELeak issueCheck the supply hose connection, the filter, the levelling feet, and use dishwasher detergent onlyThe leak continues, or the pump gaskets, tub or dispenser look damaged
5C or 5EDrainage issueStraighten the drain hose and clean the filterThe drain pump is blocked or the problem persists
4C or 4EWater supply issueOpen the supply valve and clean the valve filterThe valve or control board is at fault

Read more on Samsung dishwasher repair in Dubai.

LG Dishwasher Error Codes: What Do OE, IE and HE Mean?

On an LG dishwasher, OE means the tub is not draining fully, IE means it is not receiving enough water and HE means water is not heating. OE and IE have owner checks. HE, tE and LE need a technician. LG says its codes can vary by model.

CodeWhat LG saysReset or call
OEOutlet error. Tub not fully draining. Clean the filter, straighten the drain hoseCheck, then call if water pools above the filter
IEInlet error. Tub not receiving water. Check the taps and the inlet hose for kinksCheck, then call if it continues
AE, EI or FELeakage or overfillingCheck level and detergent, call if it continues
bEBubble error from oversudsing. Stop using dish soapFix the detergent, call if it appears with no suds
HEHeater error. Water is not being heatedCall
tETemperature sensor problemCall
LECleaning motor problemCall

LG advises cleaning the filter every one to two weeks after the machine has cooled for 30 minutes. See LG dishwasher repair in Dubai.

What Is Aquastop, and What Should I Do About Water on the Floor?

AquaStop is Bosch’s leak-protection system. It senses a leak, shuts off the water supply automatically and alerts you on the control panel. If the code appears, close the tap, switch off and mop up. Do not reset the machine to test whether it is fixed.

Other brands handle leaks with their own codes, such as Samsung LC and LG AE, EI or FE. The sequence is the same for all of them:

  1. Close the isolation tap.
  2. Switch off at the breaker and mop up.
  3. Look at the door seal, and for foam from washing-up liquid.
  4. Leave the machine off and call if the water returns.

Money-saving tip: Send us the code and a photo of the water source before the visit. It helps the technician bring the right part and keeps the diagnosis short.

Why Does Dubai Make Dishwasher Error Codes More Likely?

Dubai kitchens bring hard water, power dips and compact layouts together. Limescale blocks filters and heaters, power dips can disturb the board, and tight cabinets kink hoses. Each links to a different code group, so check the cause before you assume the machine is at fault.

Commercial kitchen with stainless steel dishwashing equipment
Photo by Ricardo Gomez Angel on Unsplash
  • Hard water: Limescale can clog filters and coat heaters, linking to drain, filter and heating codes. Bosch lists E12 for limescale in the heat pump.
  • Power dips: Bosch lists E27 for a low house power supply. A momentary dip can set off a code that clears on a reset.

For washing machines, see washing machine error codes in Dubai.

When Should I Call a Technician for a Dishwasher Error Code?

Call when the code involves a leak, the heater, a sensor or the board, when the same code returns after one reset, or when the filter and hoses are clear and the fault remains. Pump housing, wiring and heating work is technician only.

  • Any leak or water-protection code.
  • Any code that returns after one reset.
  • Heater, sensor, motor or board codes, or a tripping breaker.

Safety note: Do not open the machine, test the heater or touch wiring. Switch off, close the tap and call +971 54 309 2041.

How Al Siraj Fixes a Dishwasher Showing an Error Code

  1. Book and get a quote. Call or WhatsApp the code and a photo of your model label. We open 24 hours, 7 days a week, and a technician reaches your door in under 60 minutes on average.
  2. On-site inspection. The technician tests the circuit behind the code, not just the part named. A diagnostic fee may apply, usually included in the total if you go ahead.
  3. Immediate repair. You get a fixed quote before we touch it, with no hidden fees. We use genuine parts and most repairs take 30 to 60 minutes after diagnosis.
  4. Warranty and aftercare. Every repair is tested in front of you. The invoice carries a 12-month written warranty on the fault repaired. New unrelated faults and power-surge damage are not covered.

With 3,000+ clients, 7+ years in Dubai and a 95% first-visit fix rate, we repair 50+ brands. Our dishwasher repair guide for Dubai homes covers causes in more depth, and our dishwasher repair cost guide explains the price drivers. You can also book online or see our dishwasher repair page.

Dishwasher FAQs

What does the E15 code mean on a Bosch dishwasher?

E15 means the safety switch has detected water in the base and leak protection has activated. Close the water tap, switch off the dishwasher and call for service. Do not reset it to test whether the leak is fixed, because the water source needs a technician to trace it.

What does the LC code mean on a Samsung dishwasher?

LC, and LE on some models, means a leak issue. Check the supply hose connection, the filter and that the machine is level, and use dishwasher detergent only. If it continues, call for service, because worn gaskets or a damaged tub need a technician.

What does OE mean on an LG dishwasher?

OE is an outlet error, meaning the tub is not fully draining. Clean the filter once the machine has cooled, and straighten the drain hose. If water keeps pooling above the filter, LG says to request service. Codes can vary by model, so check your manual.

How do I clear an error code on my dishwasher?

Switch the dishwasher off at the breaker for about a minute, switch it back on and run a short empty cycle. If the code returns, stop and call. Fix the cause, such as a clogged filter, before you reset, and check your manual for your model.

What does E24 mean on Bosch and Siemens dishwashers?

E24 points to a blocked drain, and Bosch and Siemens both name a blocked pump as a likely cause. Check the hose for kinks and the filter. If the problem persists, close the tap, switch off and book a repair.

Is it safe to use my dishwasher with an error code?

Not if the code mentions a leak, heater or board. Switch off, close the tap and call. A simple code such as a blocked filter is fine to clear, then run one short cycle to check. If it returns, call us.

Last updated: 9 November 2026

Code on the display and the machine stopped? Call +971 54 309 2041 or send a WhatsApp with the code and a photo of your model label for a quick estimate. You can also book online.

Contact Al Siraj Electronics Repairing

Arab Bank Bldg – Office No SM1-02-710 – Port Saeed – Riggat Al Buteen – Dubai – United Arab Emirates
Phone and WhatsApp: +971 54 309 2041
Open 24 hours, 7 days a week